Service and Maintenance

Contact Rotovia Deventer Customer Service for the possibilities of service activities by Rotovia Deventer.

Replacing the cover

To remove the cover a bar can be placed between the container and the cover close to the hinge.
By opening the cover, it will pop out of the hinge. It’s now easing to release the cover by moving it sideways.
CAUTION: To avoid unnecessary damage, it’s recommended to use a plastic or a wooden bar or to apply some protection around the bar, e.g. a cloth or similar.
Service and Maintenance
Service and Maintenance
To replace the cover simply position it sideways in one hinge.
Pull the cover at the other side towards the hinge so it will snap in.
Service and Maintenance
Service and Maintenance

Replacing the frame

To remove the frame the product should be placed upside down.
The two fixed castors can be removed by pulling out the split pin, the two swivel castors can be removed by unscrewing the M8 bolts.
CAUTION: To avoid unnecessary damage, it’s recommended to use some protection on the floor, e.g. some cardboard, a cloth or similar.
M8 fasteners for assembling the swivel castors
Split pin for fixation of the fixed castors
Service and Maintenance
To release the frame, unscrew both M10 bolts and push/pull the frame towards the back side of the product.
M10 fasteners for the fixation of the frame
Service and Maintenance
Service and Maintenance
In case of the pull rod combination it’s necessary to first remove the bumper by unscrewing both M10 bolts before pushing/pulling out the frame.
M10 fasteners for the fixation of the bumper
Service and Maintenance
To replace the frame, make sure that the nylon bushes are placed in the two blind holes. The frame can now be pushed/pulled from the back side of the product towards the front until the two metal plates at the back side of the frame contact the plastic.
Polyamide bushes
Metal plates at the back side of the frame for the fixation of the frame
Service and Maintenance
Service and Maintenance
The frame can now be fixated by screwing in both M10 bolts, including a spring washer.
CAUTION: Make sure that the nylon bushes are outlined with the threaded holes in the frame before assembling the M10 bolts.
CAUTION: It’s highly recommended to apply some copper anti-seize lubricant on to the bolts before assembling them.
M10 fasteners for the fixation of the frame
Service and Maintenance
The fixed castors should be placed with a plain washer at both sides of the castor, use the split pin to fixate the castor. Tip over the ends of the split pin to prevent them from falling out.
Both swivel castors should be assembled with 4 M8 bolts, including a spring washer.
CAUTION: It’s highly recommended to apply some copper anti-seize lubricant on to the bolts before assembling them.
M8 fasteners for assembling the swivel castors
Fixed castor with a plain washer at both sides of the wheel. Split pen for fixation.
Service and Maintenance
Service and Maintenance
In case of the pull rod combination the bumper should be replaced and be fixed with two M10 bolts, including a spring washer.
CAUTION: It’s highly recommended to apply some copper anti-seize lubricant on to the bolts before assembling them.
M10 fasteners for the fixation of the bumper
Service and Maintenance

Cleaning the Drumtainer

For information on chemical compatibility of the cleaning agent regarding the Drumtainer please contact VARIBOX Customer Service.

The Drumtainer and its components can be cleaned by means of a high-pressure water jet with a maximum temperature of 60˚C. In order to clean the inside, it’s recommended to place the Drumtainer on its side under a >15˚angle for optimal drainage. Do not leave water inside the Drumtainer after cleaning to avoid misunderstanding regarding spillage or leakage.

Position of the Drumtainer for optimal drainage

The Drumtainer is designed to enclose and secure the content of the drum in case of an emergency such as drum failure or spillage during operation. The spilled content can be pumped out by means of placing a pump unit between the drum and the Drumtainer.

CAUTION: Always apply company regulations in case of an emergency.

Space for pump unit in case of an emergency